Silic One Tiecoat (Yellow)

SKU
Silic One Tiecoat

Hempel's Silic One Tiecoat 27450 is a high solid, silicone-based humidity curing tiecoat for Hempel's Silic One 77450. Secures adhesion between Hempel's Light Primer 45551 or Hempel's Silic Seal 45441 and Hempel's Silic One 77450.

As a fouling release system for boats of glass fibre, steel, aluminium and plywood. For use below the waterline.

As low as £20.29
HEMPEL / 27450

THE CONNECTION THAT COUNTS.

Hempel Silic One Tiecoat. Give your Silic One system the adhesion layer it needs. This silicone-based tiecoat connects the specified epoxy primer to the Silic One fouling-release finish below the waterline.

Hempel Silic One Tiecoat
Secure the system

The adhesion stage between Light Primer or Conversion Primer and Silic One.

Brush or roller

Apply one full coat to the correctly prepared and primed surface.

Plan the quantity

10 m² per litre theoretical coverage at the specified film thickness.

Part of a complete coating system

Use Silic One Tiecoat on the specified primer, then finish with Silic One. The tiecoat is an intermediate layer, so buying it alone does not provide the complete fouling-release finish. Hempel lists glass fibre, steel, aluminium and plywood within the system’s below-waterline applications.

Plan the application

STEP 01

Check what is already on the hull

A sound existing antifouling conversion and a bare-substrate installation need different preparation. Choose the route in the Silic One buying guide before ordering.

STEP 02

Prime using the specified route

Use Light Primer or Conversion Primer as specified for the surface. At 20°C, the current tiecoat data gives a 2–4 hour interval from these primers to the tiecoat.

STEP 03

Apply the tiecoat, then the finish

Stir thoroughly, apply one full coat and observe the current overcoating window before Silic One. Keep the lid on between pours; do not thin.

Use the current product data, safety data and substrate-specific application instructions supplied by Hempel. Temperature, humidity and film thickness affect the working and overcoating schedule.

How much do I need?

Enter the measured coated area for an illustrative estimate. Reference coverage: 10 m²/L at 70µm dry film thickness.

Use actual surface area, not boat length.
Quantity for this product stage only.
10% is an editable example, not a Hempel specification.
Theoretical quantity2.00 L
Including your allowance2.20 L

Illustrative estimate only. Estimates this tiecoat only. Primer and Silic One finish must be calculated separately. Actual use depends on surface profile, application and film build. Confirm quantities against the current Hempel specification and the supplied pack. Round purchasing quantities up to whole suitable packs; this tool does not add items to your basket.

Calculation: area × coats ÷ 10, then multiply by (1 + allowance ÷ 100). Litres are rounded up to the next 0.01L.

Technical details at a glance

Hempel Silic One Tiecoat specification
Product typeSilicone-based intermediate tiecoat
ShadeYellow / Cream · 23410
Area of useBelow the waterline, within the specified system
Theoretical coverage10 m²/L
Reference film thickness70µm dry / 105µm wet
ApplicationBrush or roller; one full coat
Working time60 minutes at 20°C
Application conditionsSurface above 10°C; relative humidity 30–85%
ThinningNot permitted

Before you order

Is this the same as Silic One?

No. Silic One Tiecoat is the adhesion layer. Silic One 77450 is the final fouling-release coating.

Can it go straight onto old antifouling?

Use the specified conversion route. Sound existing antifouling normally needs the Conversion Primer stage; failed coatings need further preparation.

Which size should I order?

Use the area calculator as an illustration, then check the specified system, losses and working time. Choose the required pack in the product options above.

Complete the right system

Specify the complete system with Marathon Leisure. Compare preparation routes, coating stages and maintenance in our Silic One buying guide. For product selection and availability, speak to your Marathon account manager.

File(s)